Fieldbus Technique

The CANtouch is a mobile measuring device for CAN-based bus systems.

The further development of the CAN-Bus Tester 2 is battery-powered and equipped with a touch display. Its intuitive user interface allows extensive measurements to be taken in the shortest possible time. The results can be archived for documentation or later analysis and further processed on the PC.

The physical layer measurements have been extended to include the direct determination of potential differences between the participants (common mode/ground shift).

With the online trigger, you can monitor the bus for individual physical limits, determine problems over time and make errors visible in the oscillogram.

The protocol monitor is used for sending, receiving, decoding, and recording messages.

CANvision is the most used CAN software tool in our house. It is used for developing, setup and monitoring of CAN networks. Because it is network capable, it is not necessary to be present at the measuring place. See and analyze the data traffic, filter, send your own messages.

The CANalarm is a low priced analysis tool that can be installed in the bus permanently.
It makes it possible to build up a separate and redundant monitor without a change of configuration and program of the master controller. It works passive and is therefore non-reactive.
The whole device is placed into a 9-pin D-Sub plug. It is easy to implement with the autobaud function.

If the system stands still, the loss is usually high. To perform some corrective action at the right time, system components and the whole guidance system should be maintained continually. Because of wear there are worsening of running parameters of the bus system. These changes are diagnosed by our CANobserver within the running system and are notified to the facility operator.

The CAN-Bus Tester 2 is a widely used measuring device for the control of bus parameters. The success story starts already in the year 2002 with the first model. The hardware was completely redesigned in version 2. The corresponding software is still developed and has been enhanced with extensive updates.

Check the setup of the bus before you switch on with the bus wiring test, measure under running conditions down on the physical layer and analyses data of the nodes with the protocol monitor. The longtime monitor shows scattered errors and creeping signal loss.

The trigger output makes it possible to show data from only one node of the bus.

The great box contents within the service case with a big adapter set make it possible to use the device out of the box in many environments. You can save your measurements and print a status protocol directly from the software.

Proven in tens of thousands of applications, MicroControl's protocol stacks speed up software development and help designers and engineers to define interfaces. Our CANopen and J1939 protocol stacks are set for the future and offer the possibility to migrate from CAN Classic to CAN FD at any time.

Kvaser Memorator Pro 2xHS v2 is a professional-level, dual channel CAN bus interface and standalone data logger offering advanced features such as message filtering, triggers, error detection and generation, silent mode, an expandable SD card slot up to 64G, and galvanic isolation. Connected to a PC with USB2.0, the Kvaser Memorator Pro 2xHS v2 operates as a powerful real-time CAN to USB interface, whilst in data logger mode, the compact design of this device makes for the perfect flight recorder. Configurable using Kvaser's Memorator Config Tool, this device is capable of running user-developed scripts, written in the Kvaser t programming language. Guidance in creating t programs is provided. The Kvaser Memorator Pro 2xHS v2 is CAN FD compliant.

Kvaser Memorator Pro 5xHS is a five-channel, high performance, CAN (controller area network) bus interface and standalone data logger that allows users to monitor and collect data from up to five CAN channel using just one device. Standalone mode logs data to an SD card; interface mode connects to the PC via USB. This device supports CAN FD.

Designed for troubleshooting any CAN-based (controller area network) system, the Kvaser Memorator Light HS v2 is an easy-to-use tool for logging serial data, with no software setup required. With an autobaud function that determines CAN bus bit rate, the Kvaser Memorator Light can be attached to any high-speed CAN bus without configuration. All CAN bus traffic is logged in a circular buffer, overwriting the oldest data when the buffer becomes full. A separate circular buffer keeps track of error frame conditions and the message traffic that occurs near the conditions.

Kvaser Memorator R SemiPro is an advanced, rugged, two-channel CAN (controller area network) to USB interface and standalone data logger - two products in one! To ruggedize the design, Kvaser has soldered the SD card to the PCB to make sure it works error-free even when exposed to vibration and shocks. Galvanic isolation and an aluminium housing complete the package. In standalone mode, this device logs data to an SD card, whilst in interface mode, it connects the CAN bus to the PC via USB. Connect this data logger to a PC to configure baud rates, trigger conditions and filters using the Kvaser Memorator Tools software, included

The Kvaser Memorator 2xHS v2 is a compact, dual-channel CAN bus interface and standalone data logger that allows users to monitor and collect data from two high speed CAN channels simultaneously. Standalone mode logs data to an SD card; interface mode provides a real-time connection between the CAN network and a PC, via USB. As a data logger, Memorator makes for a perfect flight recorder due to its compact design. Triggers and filters can be set on this device using a user-friendly configuration program and stored on the standard SD card (supplied).

The plug & play CL1000 CAN logger records CAN bus data to an 8 GB SD card. The logger is 100% standalone (no PC required) and data is easily extracted via USB.

The CL1000 is ideal for vehicle development and field testing (cars, heavy-duty & more).

Further, the CL1000 doubles as a powerful reverse-engineering tool with live-streaming via USB in SavvyCAN or Wireshark

The plug & play CL2000 CAN logger records CAN bus data to an 8 GB SD card and timestamps it with a real-time clock.

Further, the CL2000 can operate as a CAN bus interface for real-time USB streaming.

The CAN logger is ideal for vehicle fleet management (trucks, buses, harvesters, cars, ...), prototype field testing, diagnostics or reverse engineering.

The plug & play 2xCAN/LIN logger records timestamped CAN data (Classical/CAN FD) to the extractable 8 GB industrial SD card.

It's extremely easy to use: Simply power the device via your CAN bus connector to start logging raw CAN data. Extract the data and process it using 100% free open source software/API tools - incl. J1939/OBD2 DBC conversion & graphical plots.

The CANedge1 is ideal for monitoring CAN bus systems over long periods - e.g. for legal purposes, vehicle development, diagnostics, maintenance or research.

The plug & play 2xCAN/LIN logger records timestamped CAN data (Classical/CAN FD) to the extractable 8 GB industrial SD card.

The small device connects via WiFi access points (e.g. WLAN or 3G/4G routers) to securely push data to your server. Further, the device can be updated over the air.

Ideal for telematics, R&D field tests, diagnostics and predictive maintenance. Software/APIs are free & open source - with no subscription fees or vendor lock-in.

Kvaser Air Bridge Light HS is a configuration-free wireless CAN bridge that achieves predictable latency, without sacrificing stability or range. Comprising a preconfigured pair of plug-and-play units to rapidly exchange raw CAN data, the Kvaser Air Bridge Light HS is designed for environments or situations that make wired connection unsuitable or challenging e.g. between two moving parts that are connected by CAN.

Kvaser BlackBird v2 is a high-performance wireless (WLAN) communication link for the High Speed CAN bus. More powerful and versatile a WLAN solution than Kvaser's original BlackBird, Kvaser BlackBird v2 incorporates a new radio chip with up to 75% better range. The BlackBird v2's ability to leverage existing wireless infrastructure makes it ideal for replacing the cumbersome cable, accessing hard-to-reach CAN network, or monitoring a CANbus while in motion.

The Kvaser Ethercan Light HS is a CAN to Ethernet interface that, when linked over the Internet to an Ethernet-equipped PC, allows CAN data to be remotely accessed from anywhere in the world. Ethercan makes it easy to implement the Internet of Things (IoT) concept by enabling data from any CAN product or system to be sent over a corporate network or the Cloud, using the standard Kvaser API. The Kvaser Ethercan device can be configured with a static IP and comes with an Ethercan Factory Reset Device to reset the configuration to factory default DHCP settings at the push of a button.

The Kvaser Ethercan HS is a powerful, real-time Ethernet to CAN interface that, when linked over the Internet to an Ethernet-equipped PC, allows CAN data to be remotely accessed from anywhere in the world. Built-in Power over Ethernet (PoE) eliminates the need for a separate power cable when you can't power the device from the CAN bus. Kvaser’s Ethercan product range makes it easy to implement the Internet of Things (IoT) concept by enabling data from any CAN product or system to be sent over a corporate network or WAN, using the standard Kvaser CANlib API. Users of the Kvaser Ethercan HS can also choose to connect to the device using the built-in REST API for web-enabled devices, such as smartphones. As a programmable interface, the Kvaser Ethercan HS is suited to advanced applications, such as ECU reflashing. For example, a program could be created to process CAN messages locally in the device, removing the latency of WiFi and/or Ethernet.